Vertical Foam Bladder Tank for Fire Fighting

• Customization: Available
• Tank Capacity: 500-10000L (130~2650 Gallon)
• Flow Range: 4-360L/S (63~1513gpm)
• Model NO.: PHYM
• Proportioner Size: Dn80~Dn250 (3"~10")
• Working Pressure: 0.6MPa~1.2MPa
• Mixing Ratio: 3% or 6%
• Type: Vertical & Horizontal
• Transport Package: Crate or Pallet
• Trademark: GAN
• Origin: Shenzhen, China
• HS Code: 8424100000
• Production Capacity: 1000/Month

Product Description

Vertical Foam Bladder Tank For Fire Fighting

INTRODUCTION
The foam bladder tank is the main unit of the foam extinguishing system. The foam tank and the low/medium expansion foam generator construct the low/medium foam spraying system. It can also construct the high expansion total flooding extinguishing system with high expansion foam generator. It aims at fire of class A and class B, especially for fire of class B. The foam bladder tank mainly applied in occasions such as places where inflammable liquid was produced, stored and transported. It is especially suitable to put out fire caused by inflammable liquid tank or large scale of spill fire. 

PRINCIPLE
The device consists of pressure tank, bladder, proportioner, pressure gauge, valves and pipeline. A pump is needed to supply pressurized water. When pressurized water flow though proportioner, a small part of water (3%-6%) flow into tank from branch pipe to press the bladder to swap out equal foam concentrate and then mix with another part of water (97%-93%) to form foam solution in proportioner and provide to foam generator. 

PARAMETERS 

Proportioner Model No.	PHY4	PHY8	PHY16	PHY24	PHY32	PHY40	PHY64	PHY72
Diameter (DN)	50	65	80	100	100	150	150	150
Mixing Ratio	3% or 6%
Rated Working Pressure (MPa)	1.2
Working Pressure Range (MPa)	0.3~1.2
Rated Flow (L/S)	4	8	16	24	32	40	64	72
Flow Rang (L/S)	1~4	2~8	3~16	4~24	8~32	12~40	15~64	17~72
Pressure Drop (MPa)	≤0.2

INSTALLATION
Device should be installed at places with shelter to avoid sun and rain. Ambient temperature should be within 40°C and leave enough space for operation. Device should be installed at concrete floor and fastened with anchor nuts. 
Do the hydraulic test after installing. Open the tank vent valve first then fill water into bladder from concentrate draining pipe. Then close tank vent valve when bladder is full of water. Pressurize the system and keeping for 10 minutes when pressure gets test pressure, tank should have no leakage. Close water inlet valve and open water drainage valve and concentrate drainage valve to drain water away in tank and bladder. (We will do this test when products leave the factory)

Horizontal Bladder Tank

1. Tank 2. Pressure Gauge 3. Water Inlet Pipe 4. Feed Inlet 5. Concentrate Outlet 6. Safety Valve
7. Tank Vent Pipe 8. Inspection Hole 9. Lifting Lug 10. Check Valve 11. Bladder Vent
12. Liquid Indicator 13. Bracket 14. Water Drainage 15. Foam Drainage 16. Proportioner

CAPACITY LITERS	D mm	L mm	L1 mm	L2 mm	B mm	B1 mm	B2 mm	H mm	H1 mm	WEIGHT (KG)
500	800	1450	630	480	1250	705	400	1400	700	280
1000	1000	1800	800	625	1350	760	330	1600	800	350
1500	1000	2350	1270	1120	1350	760	340	1650	810	450
2000	1200	2300	1230	1025	1550	1000	390	1800	900	550
2500	1200	2650	1550	1350	1550	1000	400	1850	910	700
3000	1400	2500	1320	1120	1750	1200	400	2100	1000	800
3500	1400	2800	1450	1250	1750	1200	400	2100	1000	950
4000	1500	2750	1500	1300	1850	1300	500	2200	1100	1050
5000	1600	3100	1800	1500	1950	1400	850	2300	1100	1200
5500	1600	3250	1800	1500	1950	1400	850	2300	1100	1300
6000	1600	3400	1900	1700	1950	1400	850	2300	1200	1400
7500	1800	3500	2100	1800	2200	1800	850	2500	1200	1600
9000	2000	3500	2000	1800	2400	1800	1350	2700	1300	1900
10000	2000	3850	2000	1800	2400	1800	1350	2700	1300	2200
11000	2000	4100	2000	1800	2400	1800	1350	2700	1300	2600
13000	2200	4000	2350	2000	2600	2000	1400	2900	1400	3000
15000	2300	4300	2350	2000	2700	2000	1400	3000	1460	3500

Size and weight are just for reference, real products can be different. 

Vertical Bladder Tank

1. Tank 2. Pressure Gauge 3. Water Inlet Pipe 4. Feed Inlet 5. Concentrate Outlet 6. Safety Valve
7. Tank Vent 8. Inspection Hole 9. Lifting Lug 10. Check Valve 11. Bladder Vent
12. Liquid Indicator 13. Bracket 14. Water Drainage Valve 15. Foam Drainage 16. Proportioner

CAPACITY LITERS	D mm	L mm	L1 mm	B mm	B1 mm	H mm	H1 mm	WEIGHT (KG)
500	800	810	600	1000	1150	1700	1200	280
1000	1000	1010	800	1200	1350	2100	1200	350
1500	1200	1210	1000	1400	1550	2100	1200	450
2000	1400	1410	1200	1600	1750	2050	1200	550
3000	1400	1410	1200	1600	1750	2450	1200	800
4000	1600	1600	1400	1800	1950	2800	1200	1050
5000	1700	1680	1500	1900	2050	3000	1200	1200
6000	1800	1760	1600	2000	2150	3300	1200	1400
8000	1900	1820	1700	2100	2250	3800	1200	1600
9000	2000	1920	1800	2200	2350	3900	1200	1900
10000	2200	2120	2000	2400	2550	4300	1200	2200

Size and weight are just for reference, real products can be different. 

Packaging & Shipping



Company Information

With a history of more than 20 years, Shenzhen Winan Industrial Development Co. Ltd. Is a professional manufacturer and exporter who are focusing on designing, developing and manufacturing all kinds of Fire fighting equipment. The company now has a large area of industrial workshops of more than 10000 square meters, located in Shenzhen, China, with convenient transportation access. 




All of our products comply with international quality standards and are greatly appreciated in a variety of different markets throughout the world. Our well-equipped facilities and excellent quality control throughout all stages of production enables us to guarantee total customer satisfaction. As a result of our high quality products and outstanding customer service, we have gained a global sales network around the world. 

Certification


FAQ: 

1. Do you offer free sample for your clients? 

Yes, we can offer you free sample. 

2. What's the MOQ of your products? 

MOQ is ONE PCS/set. 

3. Are you manufacturer with your own factory? 

Yes, we are the manufacturer for more than 20 years

4. What's your payment terms? 

We accept T/T, L/C, Western Union, Paypal, etc. 

5. How long is the delivery time? 

Usually around 15 days after payment. 

6. Can you accept OEM? 

Yes, we do customized design for our clients. 


Contact Us: 

Shenzhen Winan Industrial Development Co., Ltd. 

No. 18, Fengshun Road, Tongle, Longgang District, Shenzhen City, Guangdong, China 

 

Website: HTTP: //www. Winanfire. COM